您好，歡迎訪問鄭州潤瑪塑業有限公司官網！
產品中心
PRODUCTS CENTER
產品描述
加藥箱實地操作應用
PE加藥箱裝置根據所需藥劑濃度，在攪拌箱內配制，經攪拌器攪拌均勻后投入溶液箱、用計量泵（加藥泵）向投藥點或指定的系統中輸送所配制的溶液。成套加藥裝置具有結構緊湊、安全簡單、操作使用簡便等特點。該裝置還可根據用戶不同工藝流程的要求，進行有針對性的設計、配置必要的部件，實現功能適合（如自動遠程控制）、經濟實用。
滾塑原料 / Raw materials of Rotomoulding
線性低密度聚乙烯（LLDPE）是理想的滾塑原料。LLDPE是乙烯與丁烯、乙烯等的共聚物，分子呈線型結構，密度為0.93g/cm3.。LLDPE用于滾塑的優點在于流動性好、熱穩定性好、耐環境應力開裂性好、抗沖擊性能好、剛性好。
LLDPE(Low Linear Density Polyethylene)is the ideal raw materials for rotomoulding.LDPE is the copolymer of polythene,butylenes and so on with the linear molecule and the density of 0.93g/cm3.The advantage of LLDPE is it is better in liquidity,thermal stabilization and ESCR < impact,and hardness.
滾塑設備 / Equipment of Rotomoulding
對滾塑設備的基本要求是能模具繞兩個互相垂直的旋轉，模具在旋轉的同時還能被加熱和冷卻。滾塑設備一般包括轉臂、熱室和冷室三部分。按加熱方式可分為直火加熱式、熱室空氣加熱式、夾套加熱式、熔鹽拋灑加熱式、紅外線加熱式和電加熱式。
The basic requirement for rotomoulding equipment is to make the molder revolve around the two vertical when the molder can also be heated or cooled.The equipment usually consist of the three parts of rotational arm,heating room and cooling room.According to the way of heating.it can be divided into open fire,air heat,molten salt spreadultra red,and electronics.
相關產品
產品描述
加藥箱實地操作應用
PE加藥箱裝置根據所需藥劑濃度，在攪拌箱內配制，經攪拌器攪拌均勻后投入溶液箱、用計量泵（加藥泵）向投藥點或指定的系統中輸送所配制的溶液。成套加藥裝置具有結構緊湊、安全簡單、操作使用簡便等特點。該裝置還可根據用戶不同工藝流程的要求，進行有針對性的設計、配置必要的部件，實現功能適合（如自動遠程控制）、經濟實用。
滾塑原料 / Raw materials of Rotomoulding
線性低密度聚乙烯（LLDPE）是理想的滾塑原料。LLDPE是乙烯與丁烯、乙烯等的共聚物，分子呈線型結構，密度為0.93g/cm3.。LLDPE用于滾塑的優點在于流動性好、熱穩定性好、耐環境應力開裂性好、抗沖擊性能好、剛性好。
LLDPE(Low Linear Density Polyethylene)is the ideal raw materials for rotomoulding.LDPE is the copolymer of polythene,butylenes and so on with the linear molecule and the density of 0.93g/cm3.The advantage of LLDPE is it is better in liquidity,thermal stabilization and ESCR < impact,and hardness.
滾塑設備 / Equipment of Rotomoulding
對滾塑設備的基本要求是能模具繞兩個互相垂直的旋轉，模具在旋轉的同時還能被加熱和冷卻。滾塑設備一般包括轉臂、熱室和冷室三部分。按加熱方式可分為直火加熱式、熱室空氣加熱式、夾套加熱式、熔鹽拋灑加熱式、紅外線加熱式和電加熱式。
The basic requirement for rotomoulding equipment is to make the molder revolve around the two vertical when the molder can also be heated or cooled.The equipment usually consist of the three parts of rotational arm,heating room and cooling room.According to the way of heating.it can be divided into open fire,air heat,molten salt spreadultra red,and electronics.